Advertisement

Leaf-casting a rhubarb leaf

How to do a leaf-casting!

Leaf-casting a rhubarb leaf

A serendipitous discovery of a large leaf in a mountain stream, led me to try molding it with a concrete mix and creating a lovely mold and save the leaf as a garden art piece.

Indian Rhubarb, Darmera peltata

Recently I happened to go on a drive up to the high country on an errand. It’s a great place for an errand, so I packed a dinner picnic and we packed up the dog and headed up towards Whiskey falls, a spot in the mountains near our home.

After Tractor Man, now ‘Motorcycle Man’, had finished getting the correct mileage for a section of the dualsport ride he was planning, we were all set for dinner.

Sitting in front of the Falls about to bite my dinner, I happened to see that the large leafed plants called Indian Rhubarb were at their peak and filling the stream banks below the falls.
That is how it came that there were two huge leaves sitting in water bottles on my kitchen counter.

We had Whiskey Falls to ourselves in early July. This is how close you are while munching on a panini!

 

The next morning…

Next morning, I cast the leaf with cement mix!

Supplies needed:

Leaf, Rhubarb, elephant ear or any large leaf
Sand
Portland cement
dry cleaning bag
kitchen trash bag

The recipe I used was 2 quart scoops of Portland cement and 6 quart scoops sand for two leaves. I mixed the ‘batter’ as thick as Brownie batter.

The leaves laid out on the plastic covered mounds of sand

I lay a kitchen trash bag on the table, then the mound of sand. I poured sand on the table surface about 5 inches high and placed the first leaf one arranging the leaves around.

I placed one layer of the dry cleaning bag over the sand, BEFORE putting the leaf down. That kept the sand away from the cement.

 

Covering the leaf with the ‘batter’

I sprayed the leaves with Pam and carefully covered the leaf with a half inch of the cement mix, thicker in the middle and a good half inch at the edges for my first try. I patted the surface which made it nice and smooth.

Plastic allows the concrete to dry slowly, preventing cracks

I covered the entire project with a kitchen trash bag finished about 10:30 or 11am so I needed to wait 24 hours to ‘unmold them.

Now, just wait 24 hours!

Next day…

About 23 hours later (Yes, I was excited!):

I carefully reached under through the sand hill and lifted up the leaf casting, with the leaf still attached. I was amazed how well the leaf itself still looked, still green but looking a bit ‘cooked’

Advertisement

Ta-da!

Since I had sprayed the leaves with Pam so it came off pretty well, an astounding process, REALLY FUN!!

Every detail shows,….how nice!

See the mound of sand that the leaf was placed on before the cement was put on?

The leaf was easy to pull off. Isn’t it neat how it worked?

Completely un-molded

This is how thin the casting turned out. Without using a bonding agent or strengthening fibers, this thickness seemed very stable, not too fragile, although, believe me I was VERY careful.

 

The concrete shows all the veins of the leaf

See the ridges and design? You can see how the cement ran past the leaf edges at the top. I need to figure out how to stop that.

The finished ‘leaf.’

All finished except for paint and some kind of mounting to hold it above the ground just a bit.. A grouping of these might look nice. The instructions say use watered down paint for a ‘washed’ look.

With a bit of the extra cement mix, I molded up a tiny mushroom.

With a bit of the extra cement mix, I molded up a tiny mushroom.

***

About Indian Rhubarb

Darmera peltata is the only plant in its genus and some say the largest saxifrage in the world. A perennial grown from a rhizome, it’s found along streams in Northern California and southern Oregon. It’s native to California and can be found at Annie’s Annuals in Richmond CA. It needs its feet in water, I was surprised to see.  It has stunning fall color and in the winter droops down along Whiskey Falls looking very dejected, as shown in the photo below at the top of the falls.

Whiskey Falls in late November

Maybe it would grow in our ravine where the water comes down as a trickle, even in summer.

 

More:

Make your own concrete planters

How to make an easy stepping stone

12 Unique hypertufa projects for the garden

 

Sue Langley

Sue Langley, a passionate gardener and photographer lives and gardens with her husband and Corgi, Maggie on 7 acres just south of Yosemite, Zone 7 at 3000 feet. She manages the Flea Market Gardening Facebook page and website.

View Comments

  • Jeanne Sammons says:

    Indian rhubarb ...that's a new one for me! How interesting ...love the leaf's texture & shape!
    How cool to picnic in that beautiful area! Wow! & to bring home a treasure besides!
    Your leaf-cast turned out to be gorgeous! Love it!

Recent Posts

Boat gardens sail away…with our hearts

Grow, Grow, Grow, Your Boat... These boat gardens are beautiful, colorful, and well grown.  It looks like a lot of… Read More

4 years ago

Decorate your garden with blue!

'Paint' Your Garden with Blue... Is your garden is singing the blues? Mix recycled containers and crafts with blue flowers… Read More

4 years ago

Lost and Found in the Garden

See this hilarious and sometimes poignant list of lost items in the garden Question.......what was the last thing you lost… Read More

4 years ago

Jeanne’s garden Baker’s rack

Designing a charming garden baker's rack When I first saw Jeanne’s well-arranged and simply delightful Baker’s rack, I thought, ‘Somebody… Read More

5 years ago

Billie’s Yellows in the garden

Choosing a color from 'Over the Rainbow Garden' Billie Hayman's garden is full of color and she shows how one… Read More

5 years ago

Alliums in the garden, real & crafty!

Alliums are drama queens in the garden! Whether real flowers, grown from bulbs or the crafted faux flowers modeled after… Read More

5 years ago
Advertisement